Step-by-Step Methods for Adjusting a Carburetor

Simple methods for adjusting your carburetor with no special equipment required

Co-authored by Hovig Manouchekian and Ali Garbacz, B.A.

Last Updated: March 17, 2024 Fact Checked

You don’t need to be a professional engineer to adjust the carburetor in your vehicle. If you notice your engine is running a bit rough, it’s important that you go in and adjust the air and fuel mixture and find the correct idling speed of your carburetor. Fortunately, this can all be done in just a few simple steps, and it requires no special tools or equipment. Keep reading to learn how to adjust your carburetor so your engine runs smooth and stays in great shape for a long time to come.

Things You Should Know

Start your engine and let it warm up to its normal operating temperatures.
Listen to your engine. If the engine runs rich, there will be no unusual sounds, and if it runs lean, it will ping at higher RPMs (revolutions per minute).
Bring your engine to a lean mixture by turning its screws a quarter-turn at a time, counter-clockwise. Then, slowly bring them back to equal.
Tighten the idle adjustment screw to increase idling speed and loosen the screw to decrease idling speed.

Get Car Support Solve Any Problem

Hi there! Do you have a question about how to diagnose or fix a problem with your car? I’ve read the manual so you don’t have to. Select your make, model, and year, then ask away!

*

Method 1

Method 1 of 2:

Adjusting the Air and Fuel Mixture

Download Article

1
Locate the air filter and remove it. On most cars, you'll need to remove the air filter to expose the carburetor and adjust it. Open the hood and make sure the engine is off before locating the air filter and removing the assembly. Unscrew the wing-nut and any other connectors, and then remove the air filter entirely.^{[1]
X
Research source}
- Depending on your make and model and the engine type, the air filter could be in any number of different places on the engine. Consult the owner's manual or the shop guide for your vehicle.
- On most carbureted cars, the air cleaner housing is attached directly to the carburetor.
2
Find the adjustment screws on the front of the carburetor. These often look like flat-head screws. There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture.^{[2]
X
Research source}
- These often look like flat-head screws, and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.
- Some carburetors, such as the Quadrajet found in most GM vehicles, have a special screw and require a specific adjusting tool. The Quadrajet uses a Double "D" carburetor adjusting tool.
- Other carburetors may have a 4 corner idle mix adjustment and will therefore have 4 idle mixture screws.
Advertisement
3
Start the engine and let it warm to normal operating temperature. Check the temperature gauge to know when it's at the appropriate running temperature. Then, listen to the sound of the engine to get some sense of the adjustments that need to be made.
- An engine that runs lean will ping at higher RPM (revolutions per minute) when the throttle is open, as if you were flooding a gear. In this case, more gas needs to be added to the mixture.
- An engine that runs rich won't necessarily make a change in sound, but you'll be able to smell it. In that case, reduce the amount of gas. An engine that runs too rich at idle will cause the plugs to be fuel-fouled, leading to a vehicle that is harder to start cold.
4
Adjust both screws equally and find the right mixture. Adjusting the carburetor is a lot like tuning a guitar. Use a screwdriver to turn the screws equally, smoothly, and slowly until you find the sweet spot. Regardless of whether or not the engine is running too rich or too lean, bring it down to a very lean mixture by turning both screws a quarter-turn at a time, counter-clockwise, then slowly bringing them back up to an equal and smooth mixture.^{[3]
X
Research source}
- Listen to the engine to know when you’ve found the right balance. The engine should purr smoothly once you’ve found the right mixture. Any raggedness or rattling is a sign of too lean a mixture. Keep turning until you find the sweet spot.
- Use a scanner to check the air-fuel mixture of the vehicle to help you get the right adjustment.^{[4]
  X
  Expert Source
  
  Hovig Manouchekian
  Auto Repair & Design Specialist
  
  Expert Interview. 23 February 2021.}
5
Replace the air filter assembly. When you've got the carburetor adjusted, put the air filter back on and you're ready to roll.
- If you need to adjust the idle speed as well, wait to put the air filter back on until you're finished.

Method 2

Method 2 of 2:

Adjusting the Idle Speed

Download Article

1
Remove the air filter to access the carburetor. Make sure the engine is off before locating the air filter and taking it out. Unscrew the wing-nut and any other connectors, and then remove the air filter entirely.^{[5]
X
Research source}
- Consult the owner’s manual or shop guide to find out the exact location of your air filter, since it can vary depending on your make and model and engine type.
- On most carbureted cars, the air cleaner housing is attached directly to the carburetor.
There is an idle speed screw that adjusts the opening of the throttle plate, and an idle mixture screw that limits the flow of fuel at idle. You want to adjust this second screw. As always, consult the owner's manual or shop guide for your make and model, if you can't find the screws.^{[6]
X
Research source}
Just as you did with the fuel/air mixture, let the engine warm up some to make sure you're adjusting at actual running condition.^{[7]
X
Research source}
Turn the screw clockwise, no more than a half-turn, and listen to the engine. Most owner's manuals will have an optimum speed to set the idle, though you have some wiggle room if you prefer it higher or lower. Consult you owner's manual for the number and consult the tachometer as you adjust.^{[8]
X
Research source}
It should take about 30 seconds for the engine to adjust to the change you made, so wait a bit before making another adjustment. Make slow turns and listen closely to the response.
When you've got the idle adjusted to the proper specifications, or to your own preferences, kill the engine and replace the air filter to finish the job.

Expert Q&A

Search

Add New Question

Question

How do you tell if a carburetor is rich or lean?

Hovig Manouchekian
Auto Repair & Design Specialist
Hovig Manouchekian is an Auto Repair and Design Specialist and the Manager of Funk Brothers Auto, a family-owned business operated since 1925. With over 30 years of experience in the automotive industry, Hovig specializes in the process of auto repair and maintenance. He is also very knowledgeable in common automotive issues and needs including engine repair, battery replacement, and windshield accessory and maintenance. Hovig's knowledge and hard work have contributed to Funk Brothers Auto winning Angie's List Super Service Award for five consecutive years.

Hovig Manouchekian

Auto Repair & Design Specialist

Expert Answer

Take the vehicle to a mechanic and have it scanned to check the air-fuel mixture of the vehicle. Then, there's special tooling you can use to get those readings adjusted properly.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 13 Helpful 16
Question

How do you maintain a carburetor?

Hovig Manouchekian
Auto Repair & Design Specialist
Hovig Manouchekian is an Auto Repair and Design Specialist and the Manager of Funk Brothers Auto, a family-owned business operated since 1925. With over 30 years of experience in the automotive industry, Hovig specializes in the process of auto repair and maintenance. He is also very knowledgeable in common automotive issues and needs including engine repair, battery replacement, and windshield accessory and maintenance. Hovig's knowledge and hard work have contributed to Funk Brothers Auto winning Angie's List Super Service Award for five consecutive years.

Hovig Manouchekian

Auto Repair & Design Specialist

Expert Answer

Inspect the carburetor for carbon buildup—they're notorious for that. If there is buildup, you'll need to clean it.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 6 Helpful 9
Question

How do I identify two screws in a carb that's idle mixture and idle screw?

Community Answer

These screws usually are in the place where the fuel lines lead to the carburetor. If not, refer to your service manual or search online for the part number.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 21 Helpful 42

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Tightening the idle adjustment screw increases idling speed while loosening the screw decreases idling speed.

Thanks
Helpful 43 Not Helpful 26
If after adjusting the idle mechanism, the engine does not run smoothly, go back to making air and fuel adjustments and repeat the steps for both air and fuel and idling adjustments.

Thanks
Helpful 28 Not Helpful 18
If your car is equipped with a tachometer, you can use this as a tool to adjust idling speed (revolutions per minute or RPMs). Check your owner's manual for the correct RPMs.

Thanks
Helpful 28 Not Helpful 26

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Remember that when you are working on a carburetor, you are working with a fuel source. Take all necessary precautions for working around gasoline, such as wearing gloves and protective eyewear.^{[9]
X
Research source}

Thanks
Helpful 0 Not Helpful 0
Keep in mind you are also working on a running motor. You can seriously injure yourself or damage your engine if you are not careful. Work slowly and thoughtfully and make sure your clothes don't have any hanging strings or cords that could catch in the engine.^{[10]
X
Research source}

Thanks
Helpful 0 Not Helpful 0